Direct electroless Ni-P deposition on AM50 magnesium alloy from sulfate bath

A bright electroless Ni-P deposition on AM50 magnesium alloy in a sulfate plating bath was proposed by using direct plating process with non-chromate pretreatment. The electroless Ni-P plating on AM50 magnesium alloy has an admirable appearance and good adhesion. The results indicate that the electroless Ni-P deposition with non-chromate pretreatment has better adhesion than that of zinc immersion coating. Anodic polarization curves indicate that the electroless Ni-P deposition obtained from the sulfate bath has similar corrosion-resistance to that obtained from basic nickel carbonate bath. The deposition process generates less pollutant by a non-chromate plating bath and is suitable for the magnesium alloys manufacture because of its low cost. The hardness of the electroless Ni-P plated AM50 is about HV 720.6 and HV 969.7 after heat treatments at 180℃ for 2 h. The wear resistance of Ni-P plated magnesium alloy specimens is about 5 to 9 times as high as that of bare magnesium alloys.     

A novel laboratory bench for practical evaluation of catalysts useful for simultaneous conversion of NOx and soot in diesel exhaust

This study deals with the development of a laboratory bench for the practical evaluation of catalysts that are useful for the direct conversion of NO_x and soot in the exhaust of diesel engines. The employed model exhaust is generated by using a diffusion burner with additionally dosing some gaseous components to the burner gas to obtain a realistic feed composition. The produced soot is extensively characterized by employing thermogravimetry, transmission electron microscopy, N₂ physisorption and temperature programmed techniques. The results of the different characterization methods show that the present soot is suitable for the intended catalytic investigations. The simultaneous conversion of NO_x and soot is examined like in practice, i.e. the soot is separated from the tail gas by a diesel particulate filter (DPF) that is coated with the catalyst. The deposited soot is then catalytically converted by NO_x and O₂ to form N₂ and CO₂. The conversions of NO_x and soot are measured by exclusively applying gas analysers, whereby a special experimental procedure is developed to determine the soot removal. Hence, additional soot related analytics are not required. To show the suitability of the constructed bench a Pt/Fe₂O₃/β-zeolite sample is taken as test catalyst that is reported to be very active in NO_x/soot reaction. The measurements performed with and without catalyst clearly show the effect of the used sample in simultaneous NO_x/soot conversion. We therefore consider the constructed laboratory bench to be a useful tool for testing and ranking catalytic materials.     

舰船导航信号发生器虚拟化设计

介绍了基于PC总线的便携式舰船导航信号发生器虚拟化设计，着重叙述该仪器硬件设计、基于虚拟仪器开发平台LabWindows／CVI的软件设计。     

催化部分氧化法制氢的水碳比控制与探讨

简要介绍了国内少有的干气催化部分氧化转化制氢工艺,重点讨论了转化水碳比的控制条件,对降低水碳比操作进行了有益地探讨。     

高非线性光纤及其应用

介绍了各种高非线性光纤的原理，并对其在超连续（SC）脉冲的产生和波长变换上的应用作了讨论。     

光纤喇曼放大器的功率转换效率分析

在定义光纤喇曼放大器(FRA)功率转换效率(PCE)的基础上,考察了不同工作条件下光纤喇曼放大器的功率转换效率,分析PCE与光纤喇曼放大器的输入信号功率、输入泵浦功率和光纤长度的关系,比较了分布式与集总式FRA的功率转换效率,给出提高FRA功率转换效率的途径。     

直流非转移弧等离子喷枪中电弧的工作特性研究

利用计算机数值模拟技术，采用有限容积方法，针对自制的低能耗、高效率内送粉等离子喷涂设备，对喷枪内部电弧长度及其对流体特性的影响进行了分析研究。结果表明，通过增加进气流量和减少电流的大小，均使得等离子电弧长度增加，阳极弧根位置逐渐向下游移动，但是产生这两种现象的机理以及对气流温度和速度的影响是不同的。     

等离子喷涂燃料电池连接板LSM薄膜的性能研究

采用等离子喷涂法在SUS 430连接板基体上制备了LSM(La0.8 Sr0.2 MnO3)薄膜。用X射线衍射仪、扫描电镜和电子探针分别研究了喷涂前后LSM的相组成、薄膜的表面形貌和元素分布。用图像分析法计算了薄膜的孔隙率。二支点法测量了有与无LSM薄膜的SUS 430基体在130～800℃时的电导率。结果发现,薄膜与基体结合良好,薄膜孔隙细小,均匀分布,且非连通;LSM的相组成在喷涂前后保持一致;当温度<330℃时,有LSM保护膜的连接板的电导率小于无LSM薄膜的连接板的电导率;温度>330℃,结果相反。有LSM保护膜的连接板在空气中,130～800℃下,最大电导率为0.60Ω-1·cm-1。     

Innovation in milk powder technology

Global trade in preserved milks is on the increase as new markets open up in regions of the world that have not been traditionally associated with milk consumption. Equally, a rise in world milk production is forecasted to continue, and the indications are that significant quantities of the extra milk produced will be converted to commodity products such as butter and powders. Consequently, on-going investment in new spray drying capability is likely to track geographical shifts in milk production. Successful application of advanced process control to the operation of large scale drying plant is both a priority and a challenge.
  Meanwhile, opportunities for the exploitation of milk as a source of functional ingredients are being availed of by the dairy industry as it continues to achieve added value and unique key selling points. Recent research on the role of spray drying, along with other processes in the development of dairy ingredients for applications in chocolate and the preparation of microencapsulated powders, is reviewed.     

基于LonWorks和DSPs的智能节点

本文提出了一种基于LonWorks和DSPs的智能节点设计方案，并给出了具体的实现方法。该方案简单、可靠，充分利用了LonWorks强大的网络性、可靠性和DSPs强大的数据处理能力，大大提升了节点的智能化程度。